East German issue PBF gas mask kit, these were issued to troops like the Grenztruppen during the mid to late 80s. Produced and imported from the Soviet union. They had special rubberized carriers that were smaller than the standard ones and had different pockets.

Read More

An M17-series chemical-biological mask, when properly fitted and worn with the hood, protects against field concentrations of all known chemical and biological agents in vapor or aerosol form. Filter elements, in the cheeks of the facepiece, remove the agents from air entering the mask.

Read More

Made from olive-tan rubber, the original CM-3 has the inlet/exit valve constructed out of brown bakelite. The eyepieces are glass, held on with crimped metal and fabric. Air enters the mask via Tissot tubes and exits through the exit valve/voice diaphragm. The voice diaphragm contains a metal mesh (similar to a wire kitchen sifter) covering it, it also has a thin plastic disc behind the …

Read More

Set includes two (2) O-ring filter intake seals, two (2) circular outtake seals, and one (1) plastic voice diaphragm/amplifier. Designed for Parcil's full face respirators (PD-100 and PD-101). This is not compatible with the ST-100X. For help, check out Reconstructing a Parcil Safety Full Face Respirator Gas Mask.

Read More

The voice diaphragm is a circular grated metal bit on the left side and it gets highly saturated in just a few minutes. I suspect with time it may begin to rust. It is a bit easier to breath in and does not fog up all too much with heavy breathing. Overall, it's a decent panoramic gas mask, but your fitment may vary and the distortion is a ...

Read More

Answer (1 of 3): For a gas mask designed to guard against a biological threat, a very fine particulate filter is useful. An anthrax bacteria or spore might have a minimum size of one micron. Most biological particulate filters remove particle sizes …

Read More

Overview: Parcil Safety's premier PD-100 Full Face Respirator Tinted Gas Mask is a comprehensive solution for users seeking protection for their eyes, face, nose, mouth, and airways. Designed to safeguard the wearer during a variety of activities from home improvement to industrial occupations, the PD-100 is dependable for strong protection against organic …

Read More

The gas masks are mainly full face mask-filter type gas mask and half mask-filter type gas mask half. [1] When wearing a gas mask, users must first choose the appropriate mask according to their head size. Second, adjust the middle and upper headbands to the proper position, and loosen the lower headband. Hold the mask on both sides with both ...

Read More

MIRA Safety's CM-7M is a full-face respirator/gas mask. Depending on what level of protection is required, it uses standard NATO filter cartridges. For example, the MIRA Safety CBRN filter protects against a wide range of harmful and toxic substances. The mask is constructed from a material called bromobutyl rubber.

Read More

A speaking diaphragm face piece has been developed by the Mine Safety Appliance Company, Pittsburgh, Pa., to make it possible for the wearers of gas masks to carry on audible conversations without ...

Read More

After the Sino-Soviet split, the need for domestically produced standard-issue gas masks arose. The PLA at the time was mostly using a mixture of captured Japanese masks, the Type 59, and the Shm-41. Production of the mask began in 1964. The mask has a combined translucent plastic voice diaphragm and exhale valve assembly, held on to the mask with wire and tape …

Read More

Gas masks are also known as air-purifying respirators because they filter or clean chemical gases and possibly particles out of the air as you breathe. This type of respirator includes a facepiece or mask, and a filter/cartridge (if the filter is in a …

Read More

Template:Mask The LAG (Light Anti gas) MK II was a British gas mask designed during the Second World War, first issued in 1943. The LAG was designed to remove the cumbersome hose and filter of the earlier British army gas masks, using a 60mm threaded filter attaching directly to the left cheek. The LAG was first used operationally by paratroopers and other assault units on …

Read More

A voice transmission system for a protective respirator, having a face mask with an inhalation port and a filter attached to the inhalation port, is provided. The voice transmission system comprises a microphone assembly adapted to be located between the inhalation port and the air filter, the microphone assembly including a spacer for separating the filter from the inhalation …

Read More

Nebulae: 927. Blacksuit mask: Appears to be a modified C3, an old Canadian Military mask, which started production in the 60's and ended mid 80's. There's a few minor discrepancies, like having two filter inputs, the voice diaphragm on the front, plus all the ridges and whatnot. The lenses are a bit more sunk in and the mask doesn't go as far ...

Read More

A face mask carries a voice communication device including a circular housing having voice transmitting openings and an annular seat which receives a flexible film diaphragm. The diaphragm is clamped to the seat by an inner circular member which has voice transmitting openings surrounding a socket for receiving a plug-in microphone.

Read More

Although the voice diaphragm was a welcomed addition to American protective masks, it was minimally compatible with radio handsets of the era. Talking on a radio while masked meant juggling the handset between ear and voice diaphragm leading to confused and muffled communications. This arrangement plagued all M17 designs and was only improved ...

Read More

A sonic welded gas mask and the process for fabricating the mask. The facepiece of the mask provides apertures, appropriately shaped and dimensioned to receive gas mask components for sealing therein. ... anchoring and sealing of the plastic film diaphragm so as to achieve sufficient tension constraint in the film diaphragm that voice ...

Read More

This gas mask also features a voice diaphragm, allowing for clearer communication. Another feature is the drinking tube, which is useful for long-term use. This item also includes a NATO Approved 40mm Filter and a transport bag with MOLLE compatibility. We Also Recommend.

Read More

Complete with drinking tube for long-term use and voice diaphragm for easy communication with your squad. A cool collectible for any military collection. Sand-colored mask with …

Read More

They're gonna release the CM-8M and a voice amplifier for it and their older masks. The voice projection is terrible compared to the Avon's electronic voice projector, albeit you pay a pretty penny for the Avon. The MIRA CM-6M doesn't right now have protective outer lenses so if you get the lens scratched your SOL.

Read More

The B2g is a Yugoslav, and later, Serbian industrial mask. It is unknown what year this mask started being produced, (often speculated to have began production in 1990s) but as of 2019, it is still in production at the Trayal Corp works in Krusevac, Serbia. It's probably a copy of the MSA Ultravue/AUER s3 Structurally speaking, the B-2/G is very similar to its predecessor the B-2. …

Read More

The only thing that I wished was present in this respirator is a voice diaphragm. Seeing as this is a full-face mask, this should have provided a way for the wearer to speak with co-workers. It is almost impossible for me to talk while wearing this, which is fine most of the time since I always seem to be working alone.

Read More

devices. The optical mask permits the use in gas attacks of fire control and sim-ilar instruments which cannot be ad-justed to the eye with the standard gas masks. The diaphragm mask is the same as the service mask, except that the tube connecting the hose to the facepiece carries a diaphragm to give good voice transmission. The training mask ...

Read More

• Speaking diaphragm for clear voice communication. • Highly elasticized headharness with quick-release buckles with rollers for easy donning, simple adjustment & fast removal. • Face-piece support for maintaining shape & fitting characteristics during extra long periods of storage. • One size fits all.

Read More

The diaphragm is a gas tight seal and may be a vibrating voice diaphragm or may be the exhalation diaphragm of the mask. Such external devices have the advantage that they can be designed to be readily added to existing masks by clip-on features and the like and thus may not require structural modification of the mask itself.

Read More

Belgian Pirelli M.24, a very early interwar gas mask with some real funk to it. It's made mostly of high-quality leather, it sports proprietary 17mm threads, replaceable lenses, Tissot tubes, and a weird extra inlet. It's overall sturdy and full of features, but expensive and somewhat cumbersome

Read More

The LBM is a CBRN Military protective mask manufactured by AirBoss in Québec Canada. The mask provides 24-hours of continuous protection against Chemical Warfare Agents, and impermeable to all biological agents. The mask is operational in temperatures between -46 and 70 Celsius, and can be stored in temperatures between -55 and 60 Celsius.

Read More

Made out of a bottle for the mouthpeace, soda can, wool pads and activated charcoal for the filter. a pringles can with foil and lid for the voice diaphragm and a can and latex one way valve so I don't accidentally breathe in through the nose. Everything is made airtight with latex gloves on everything that touches my skin. 6. level 1. colachan35.

Read More

Respirator, Anti-Gas, Light (WWII) | Gas Mask and ...

Read More

The FMJ09 is the current issue gas mask of the PLA. The mask has only one filter port, with the other side having a fixed secondary voice diaphragm, like on the S10. The mask has a 6-point mesh head harness. The voice diaphragm is the typical green rubber, and there is a microphone port next to it. The mask comes sealed with a manual and a bag in a green plastic box. A …

Read More